AutoInsider Logo

Peugeot 307 electric windows working sporadically

2006 Peugeot 307 Problem

The Problem:

sometimes when the window is down it won't go up at all then it will go in jerks sometimes when I press up the window goes down

Ref#5478
CarPeugeot 307 1.6 td
Year2006
OwnerFangimo
Posted21/07/2010


More Peugeot and 307 problems


Solution 1

andrew slevin | Driver | Since: Jun 2010 | Posts: 0 | Fixes: 163 | View Garage
Suggested Solution

window winder could be broke. ok maybe switch is faulty


Posted on Wednesday 21st of July 2010
Don't understand this? Ask a question

Solution 2

paulieone | Driver | Since: Aug 2009 | Posts: 4 | Fixes: 1211 | View Garage
Suggested Solution

could be fault with door ecu and maybe the switch


Posted on Wednesday 21st of July 2010
Don't understand this? Ask a question

From Original Poster

Fangimo | Driver | Since: Jul 2010 | Posts: 0 | Fixes: 0 | View Garage
Suggested Solution

the problem is on both windows and all the switches so I don't think its the switches


Posted on Wednesday 21st of July 2010
Don't understand this? Ask a question

Solution 3

paulieone | Driver | Since: Aug 2009 | Posts: 4 | Fixes: 1211 | View Garage
Suggested Solution

Open bonnet then make sure car is unlocked .leave for fifteen mins then disconnect battery.leave disconnected for while. Reconnect battery then turn lights on then off.Hold window switch buttons for windows to go down then same again for up.Make sure you dont have any thing switched on for fifteen mins before disconnecting battery.


Posted on Wednesday 21st of July 2010
Don't understand this? Ask a question

Solution 4

paul watson | Driver | Since: May 2014 | Posts: 0 | Fixes: 4 | View Garage
Suggested Solution

if this is a switch fault you will be able to feel no resistance when
switch is operated,more likely to be in lift position,also no click
when switch is operated.remove switch by removing screw and prising out switch unit.remove wiring by moving catch on switch and pulling
plug.remove the top plate of switch(bit with coin recess).lever the 6
or so clips on the edge,i used a small penknife.lever the mirror operator vertically upwards.now you can remove the top of the switch,
bit with window image.press the thin white piece inwards on one side
and pull gentley upwards and then the other side.you should then be
able to find the small broken operator,thin white piece.glue this in
position with superglue using a cocktail stick to apply.when dry you
can add more glue between the white and black piece of switch top,
making it stronger than before,was designed to brake.replacing is just
a matter of pushing together,far easier than taking apart.


Posted on Thursday 14th of August 2014
Don't understand this? Ask a question

Solution 5

paul watson | Driver | Since: May 2014 | Posts: 0 | Fixes: 4 | View Garage
Suggested Solution

remove the door card,remove the rounded piece of plastic by pulling it
off.remove the silver surround of door handle by levering it out gently.remove four black star driver self tapping screws,lever out the
plastic clips using a forked lever.remove card,unplug switch unit and
speaker plug.remove window drive motor by removing three star self
tappers.spray the drive gear wheel with WD40 add a smear of grease.
replace motor,this may not work straight away,but after the WD has
had a little time to move about by the car being driven drag on the
motor is bound to be reduced,replace the two plug,put the card back on
door in a downward direction.replace screws and clips,push plastic
pieces back in place.


Posted on Thursday 14th of August 2014
Don't understand this? Ask a question


Ask a Question Post a Solution





Ads by Google


Twitter Icon Facebook Icon Google G+ Icon

Features

Car Problems