Peugeot 407 no crank no start

2007 Peugeot 407 Problem

Ref#21019
CarPeugeot 407 2.7 td v6 auto
Year2007
Owneradehughes
Posted15/06/2018
Ads by Google
im after a wiring diagram for starter system plz
adehughes82@yahoo.co.uk
Problem Category
Electrics, ECU, Warnings & Lights

Running Rough, Starting & Power Loss


Solution 1
1/4drive | Auto Insider | Since: Jun 2011 | Posts: 25 | Fixes: 1758 | View Garage
Suggested Solution

You can get a disk from "Emanuals online"
or Ebay.


Posted on Saturday 16th of June 2018
Don't understand this? Ask a question
Solution 2
1/4drive | Auto Insider | Since: Jun 2011 | Posts: 25 | Fixes: 1758 | View Garage
Suggested Solution

Still as it's an auto it'd be a good idea to check the inhibitor switch on the gear selector.


Posted on Saturday 16th of June 2018
Don't understand this? Ask a question
From Original Poster
adehughes | Driver | Since: Jun 2018 | Posts: 0 | Fixes: 1 | View Garage
Suggested Solution

Same as numeral safety switch ??


Posted on Saturday 16th of June 2018
Don't understand this? Ask a question
Solution 3
1/4drive | Auto Insider | Since: Jun 2011 | Posts: 25 | Fixes: 1758 | View Garage
Suggested Solution

Inhibitor switch is usually on the gear selector,
Hidden inside the centre console


Posted on Saturday 16th of June 2018
Don't understand this? Ask a question
Solution 4
whittingehame | Legend | Since: Oct 2009 | Posts: 444 | Fixes: 11727 | View Garage
Suggested Solution

Inhibitor switch same as neutral safety switch on outside of box on some cars .


Posted on Saturday 16th of June 2018
Don't understand this? Ask a question
Solution 5
1/4drive | Auto Insider | Since: Jun 2011 | Posts: 25 | Fixes: 1758 | View Garage
Suggested Solution

Your right,
I'm just old and thinking about series 1/2/3 jags.


Posted on Saturday 16th of June 2018
Don't understand this? Ask a question
Solution 6
whittingehame | Legend | Since: Oct 2009 | Posts: 444 | Fixes: 11727 | View Garage
Suggested Solution

I'm older than you and remember when it was all Borg Warner 3 speed boxes and I went down south for a week on a factory course !!!! If memory serves me right the inhibitor switch screwed into side of box with 4 Lucar terminals , 2 of which worked reverse lights .Those were the good old days !!


Posted on Saturday 16th of June 2018
Don't understand this? Ask a question
Solution 7
whittingehame | Legend | Since: Oct 2009 | Posts: 444 | Fixes: 11727 | View Garage
Suggested Solution

Can also remember some up at selector lever as you say .


Posted on Saturday 16th of June 2018
Don't understand this? Ask a question
Solution 8
1/4drive | Auto Insider | Since: Jun 2011 | Posts: 25 | Fixes: 1758 | View Garage
Suggested Solution

Sorry to the O/P and for all this remembering of old days.
What I should have remembered is rule one,
As the O/P asked I should have checked the manual.
So Fuse 8 feeds down to the relay that triggers the starter motor,
check both,
After that the relay is triggered by the multi function control module 2.
Everything else runs from the Transmission control module,
So there doesn't appear to be any interlock switches.
So if it were here with me now I'd be running a diagnostic on the gearbox modules and controls with Diagbox. after testing for power and operation on F8 and the relay.


Posted on Sunday 17th of June 2018
Don't understand this? Ask a question
From Original Poster
adehughes | Driver | Since: Jun 2018 | Posts: 0 | Fixes: 1 | View Garage
Suggested Solution

That's more helpful. If the fuse and relay are ok (will cheak tomorrow when I can get to where it's stuck) and there voltage to the starter b+ post and trigger wire then it's a faulty starter. Is that right??


Posted on Sunday 17th of June 2018
Don't understand this? Ask a question
Solution 9
1/4drive | Auto Insider | Since: Jun 2011 | Posts: 25 | Fixes: 1758 | View Garage
Suggested Solution

I normally test suspect starters with a remote starter tool,
Which is basically two wires/clips and a button in the middle.
You can buy them but for a one off just pull the small wire of the starter and connect a long jump wire to the same terminal,
Now the other end of the wire you touch the battery pos+ and if the starter/wires are good it'll spin over.
Doesn't even need the key on.
BUT DO MAKE SURE IT'S NOT GOING TO ROLL.
I've seen people being run over by the car they're working on drive off un driven as it were.
'course if the keys in the run position and the starter spins it ought to start and run.
If not then it's electrical.


Posted on Sunday 17th of June 2018
Don't understand this? Ask a question
Ask a Question Post a Solution


More Peugeot and 407 problems

Peugeot Problems 407 Problems

Social Media

Twitter Icon Facebook Icon Google G+ Icon

Car Problems - can you help?


Run an Auto Business?